Compare · job: rebar tying · stage: frame and structure
Rebar tying, side by side
Every tool on the record for rebar tying: 6 robots, from Autonomous Mobile Tying Robot, GRID, SkyMul rebar tying robot and T-iROBO Rebar onwards, in alphabetical order. On the record so far, none is shown on sale in the UK and between them they are sold in 3 countries. 6 carry an assessment of where they fit on a job and the catch. Each was read at the maker's own source, most recently on 13 November 2026.
ComparingAll 6 toolsChoose which
Show
Scroll right for the rest
Fact
RS-R833 · Robot · MAX Co., Ltd.Autonomous Mobile Tying Robot
RS-R1358 · Robot · Arn AutonomyGRID
RS-R1103 · Robot · SkyMulSkyMul rebar tying robot
RS-R863 · Robot · Taisei Corporation with fuRo (Chiba Institute of Technology)T-iROBO Rebar
RS-R038 · Robot · Ken RobotecTomorobo rebar-tying robot
RS-R006 · Robot · Advanced Construction RoboticsTyBot
At a glance
What it doesA self-driving robot that ties rebar crossings on a slab mat, working out its own route inside a marked area and re-routing round obstacles. Several can work the same deck together.A small battery robot that maps a rebar mat, then drives over it tying each intersection on its own while one operator supervises.An autonomous robot that places and ties rebar on a deck with little supervision, using sensors to adjust to site conditions.A small battery robot that sits on a horizontal rebar mat, drives along the bars, finds each crossing with laser sensors and ties it with wire, working an area by itself while the gang place bars elsewhere.A light rail-mounted robot that travels across a slab's top rebar mat and ties each crossing with a battery tying tool.A gantry that spans the deck and ties the rebar crossings by itself, with one person supervising.
Who it's forReinforcement contractors on large slab and deck pours.Concrete and rebar contractors on large slab and deck pours.Concrete and reinforcement contractors on large flat rebar mats.Japanese general contractors and rebar subcontractors on slabs and decks.Rebar fixing subcontractors and general contractors on flat slabs and decks.Bridge and highway contractors tying large flat rebar mats on decks.
The catchListed by the maker as under development: no specification, price or release date yet. Slabs only, as described.The maker does not state supported bar sizes, tie wire or spacing limits, and gives no price.The maker describes it as a prototype: no price or purchase terms, demo only. The maker's accuracy figures on the same page do not agree with each other.Developed by a contractor for its own sites; the page gives no sale, hire or price. Works on mats it can drive on, not on walls or columns. About 5 hours a charge.Slab mats only, bars 10-16 mm; rail must be laid and moved; tying tool extra; no price published; Japan only in the sources.It runs on the deck's screed rails or edge forms across a 10 to 117 ft width, so it suits wide, repetitive bridge decks rather than building slabs.
AssessmentReplaces one hard, repetitive job: sanding and painting, tying the mat, cutting boards, fixing the ceiling, spraying the steel. Robots built for one task. Early days: several are contractors' own robots or still in development, but this is where site work is heading. MAX's tying robot plans its own route over a slab mat, several to a deck; still in development. The catch: each does one job in set conditions, half aren't for sale, and almost none publish a price or output you can plan on.Replaces one hard, repetitive job: drilling overhead, laying tiles, tying rebar, fixing boards, setting out. Robots built for one task. Early days: many are the makers' own services or pilots rather than machines you can buy, but this is where site work is heading. Arn Autonomy's GRID maps a rebar mat and ties each intersection on its own while one operator supervises; no supported bar sizes or spacing limits are stated. The catch: each does one job in set conditions, and almost none publish a price or output you can plan on.Replaces the site walk, the man on the rebar deck and the CCTV contractor. Machines that capture or do the work on a schedule while the team is elsewhere. SkyMul places and ties rebar on a deck on its own; the maker calls it a prototype, demo only. The catch: a fleet, a dock or cameras to install and power, several are prototypes, and few publish a price.Replaces one hard, repetitive job: sanding and painting, tying the mat, cutting boards, fixing the ceiling, spraying the steel. Robots built for one task. Early days: several are contractors' own robots or still in development, but this is where site work is heading. Taisei's T-iROBO Rebar drives the mat tying crossings while the gang place bars elsewhere; Taisei's own sites. The catch: each does one job in set conditions, half aren't for sale, and almost none publish a price or output you can plan on.Replaces one hard, repetitive job: drilling overhead, laying tiles, tying rebar, fixing boards, setting out. Robots built for one task. Early days: many are the makers' own services or pilots rather than machines you can buy, but this is where site work is heading. Ken Robotec's Tomorobo travels the top mat of a slab tying each crossing; Japan only in the sources. The catch: each does one job in set conditions, and almost none publish a price or output you can plan on.Built for bridge and road decks, not building slabs. The third generation has been on sale since 2024, with 65+ projects in the US. The maker claims about 1,200 ties an hour, against 150 to 250 for a person.
Maker's figures
Speed-Not published-Not published-Not published-Not published2.7 s per tie at 200 mm pitchMaker's figure-Not published
Buying it
Sold in-To checkUnited StatesUnited States-To checkJapanCanada, United States
Not offered in-To check-To check-To check-To check-To checkUnited Kingdom
Price shapeNot publishedBy quoteNot publishedNot publishedBy quotePurchase
PriceUnder development; no price published.Buy or lease through sales; no price published; pre-order form offers 20% off.No price published; book a demo.No price published.Enquiry to the maker; rental through a Japanese hire firm, no rate shown.$425,500 standard, $455,500 fully configured, training included (maker's prices via Equipment World, Sept 2024); also as a subcontract priced per pound of installed rebar, figures not published.
Released-To check-To check-To checkOct 2017-To checkOct 2017
MakerMAX Co., Ltd. · JapanArn Autonomy · United StatesSkyMul · United StatesTaisei Corporation with fuRo (Chiba Institute of Technology) · JapanKen Robotec · JapanAdvanced Construction Robotics · United States
Every tick links to where we read it. “Not published” means the maker doesn’t say, not that it can’t. A maker’s figure is the maker’s claim, read at its source; we have not measured it. They are in alphabetical order, never by who pays.